6F5 Capping

6f5 Capping - Available Online Loose by the Tonne with Nationwide Delivery

In Stock

6F5 Capping

6f5 Capping - Available Online Loose by the Tonne with Nationwide Delivery

In stock
Enter your postcode for an accurate price
ALL QUANTITIES BELOW 10 TONNES ARE AVAILABLE IN BULK BAGS ONLY
Grouped product items
Product Name Qty
Loose Tonnes Obtain a bespoke quote for loose delivery

Grouped product items
×

How to measure?

Take a metric tape measure and measure the length, width and depth of the area to be filled. The length and width measurements should be recorded in metres and the depth in millimetres. Now take these figures and enter them into the quantity calculator to reveal the approximate quantity required for your job. 

Remember: 

1 metre is equivalent to 1000mm or 100cm 

1 centimetre is equivalent to 10mm


6F5 Capping Consists of:

6F5 is an aggregate usually composed of crushed limestone or granite although other quarried materials such as Ironstone, Ragstone or Basalt are often used. Sizes range from 100mm down to dust. The term 6F5 Capping is generally used to describe a product that is similar in size and grading to recycled 6F2 Crusher Run but made from quarried stone instead. 6F5 Capping is mainly used a sub-base for roads and buildings although it has many other uses such as Piling Mats and general backfill. The coarse nature of 6F5 makes it a very good all in one product which when compacted forms a hard wearing surface. 6F5 Capping is ideal as an initial layer of hardcore before being finished off with a layer of type 1 sized material.

Ideal for:

hard-standings, haul roads, piling mats and bulk fill.

Availability:

Loose Only

Minimum Order Quantity:

10 Tonnes Loose

Coverage:

1 tonne will cover approx 5sqm at 100mm depth

Stone Density:

Approx 1.7 tonnes per cubic metre.


More Information
Enable Google Shopping No
Content Below INSTOCK OUR MINIMUM ORDER FOR THIS PRODUCT IS 10 TONNES

Frequently Asked Questions

What is 6F5 Capping?

6F5 Capping is a product made from crushed Granite, Basalt, Gritstone or Limestone (depending on source). The size range is approximately 100mm down to dust.

What Can 6F5 Capping Be Used For?

6F5 Capping is suitable for hard-standings, haul roads, piling mats and bulk fill.

Is 6F5 Capping Suitable For A Driveway Sub-Base?

6F5 Capping should not be used as a driveway sub base. Please use either Type 1 or Type 3 for driveway sub bases.

How Do I Calculate The Quantity Of 6F5 Capping I Require?

6F5 Capping should be laid at 150-200mm depth when used as a sub base for haul roads and hard-standings. Heavier loadings will require a deeper sub-base and may need to be calculated by a structural engineer. Typically, one tonne will cover 5m2 at 100mm depth. For larger areas you may wish to use our quantity calculator located at the top right hand side of this page under the grey "How Much Will I Need" tab. Simply enter your measurements to reveal the required tonnage. Please be sure to enter the length and width figures in metres and the depth in millimetres to give the correct quantity.

How Do I Install 6F5 Capping?

6F5 Capping should be spread with and excavator and compacted with a vibrating roller in layers. It is important the product is properly compacted to prevent settling later on. The depth of installation will depend on the project but we generally recommend 150-200mm for haul roads and hard-standings.

Is 6F5 Capping Free Draining?

6F5 Capping does allow the passage of water, albeit at a slower rate than other products such as 75-40mm Clean Stone

Where Can I Buy 6F5 Capping?

6F5 Capping can be purchased right here! Larger loose orders of 10 tonnes or more will require a bespoke quote to enable us to apply any bulk discounts. A quote request can also be submitted at the top right hand corner of this page. Deliveries are usually made within 3-5 working days.